/*
	SlimeVR Code is placed under the MIT license
	Copyright (c) 2021 Eiren Rain

	Permission is hereby granted, free of charge, to any person obtaining a copy
	of this software and associated documentation files (the "Software"), to deal
	in the Software without restriction, including without limitation the rights
	to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
	copies of the Software, and to permit persons to whom the Software is
	furnished to do so, subject to the following conditions:

	The above copyright notice and this permission notice shall be included in
	all copies or substantial portions of the Software.

	THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
	IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
	FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
	AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
	LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
	OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
	THE SOFTWARE.
*/
#ifndef SLIMEVR_DEBUG_H_
#define SLIMEVR_DEBUG_H_
#include "consts.h"
#include "logging/Level.h"

#define IMU_MPU6050_RUNTIME_CALIBRATION  // Comment to revert to
										 // startup/traditional-calibration
#define BNO_USE_ARVR_STABILIZATION \
	true  // Set to false to disable stabilization for BNO085+ IMUs
#define USE_6_AXIS \
	true  // uses 9 DoF (with mag) if false (only for ICM-20948 and BNO0xx currently)
#define LOAD_BIAS true  // Loads the bias values from NVS on start
#define SAVE_BIAS true  // Periodically saves bias calibration data to NVS
#define BIAS_DEBUG false  // Printing BIAS Variables to serial (ICM20948 only)
#define ENABLE_TAP \
	false  // monitor accel for (triple) tap events and send them. Uses more cpu,
		   // disable if problems. Server does nothing with value so disabled atm
#define SEND_ACCELERATION true  // send linear acceleration to the server

// Debug information

#define LOG_LEVEL LOG_LEVEL_DEBUG

#if LOG_LEVEL == LOG_LEVEL_TRACE
#define DEBUG_SENSOR
#define DEBUG_NETWORK
#define DEBUG_CONFIGURATION
#endif

#define serialDebug false  // Set to true to get Serial output for debugging
#define serialBaudRate 115200
#define LED_INTERVAL_STANDBY 10000
#define PRINT_STATE_EVERY_MS 60000

// Determines how often we sample and send data
#define samplingRateInMillis 10

// Sleeping options
#define POWERSAVING_MODE POWER_SAVING_LEGACY  // Minimum causes sporadic data pauses
#if POWERSAVING_MODE >= POWER_SAVING_MINIMUM
#define TARGET_LOOPTIME_MICROS (samplingRateInMillis * 1000)
#endif

// Packet bundling/aggregation
#define PACKET_BUNDLING PACKET_BUNDLING_BUFFERED
// Extra tunable for PACKET_BUNDLING_BUFFERED (10000us = 10ms timeout, 100hz target)
#define PACKET_BUNDLING_BUFFER_SIZE_MICROS 10000

// Setup for the Magnetometer
#define useFullCalibrationMatrix true

// Battery configuration
#define batterySampleRate 10000
#define BATTERY_LOW_VOLTAGE_DEEP_SLEEP false
#define BATTERY_LOW_POWER_VOLTAGE 3.3f  // Voltage to raise error

// Send updates over network only when changes are substantial
// If "false" updates are sent at the sensor update rate (usually 100 TPS)
// If "true" updates will be less frequent in the time of little motion
// Experimental
#define OPTIMIZE_UPDATES true

#define I2C_SPEED 400000

#define COMPLIANCE_MODE true
#define USE_ATTENUATION COMPLIANCE_MODE&& ESP8266
#define ATTENUATION_N 10.0 / 4.0
#define ATTENUATION_G 14.0 / 4.0
#define ATTENUATION_B 40.0 / 4.0

// Send inspection packets over the network to a profiler
// Not recommended for production
#define ENABLE_INSPECTION false

#define PROTOCOL_VERSION 18
#define FIRMWARE_VERSION "0.5.0"

#endif  // SLIMEVR_DEBUG_H_