# --- DRUCKER GRUNDKONFIGURATION ---
[include mainsail.cfg]

[mcu]
# Deine Creality Board ID (Achtung: Prüf das nochmal auf dem neuen System!)
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
restart_method: command

[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 4300             # UPDATE: Basierend auf deinem Input Shaper X Test
max_z_velocity: 5
max_z_accel: 100

# --- INPUT SHAPER & ADXL (Dein neues Spielzeug) ---
#[mcu adxl]
#serial: /dev/serial/by-id/usb-Klipper_rp2040_50444667787E871C-if00

#[adxl345]
#cs_pin: adxl:gpio9
#spi_bus: spi1a

#[resonance_tester]
#accel_chip: adxl345
#probe_points:
#    110, 110, 20

# --- MECHANIK & EXTRUDER ---
[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA5
position_endstop: -10
position_max: 235
position_min: -15
homing_speed: 50

[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA6
position_endstop: -8
position_max: 238
position_min: -13
homing_speed: 50

[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC3
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
position_max: 270
position_min: -4

[extruder]
step_pin: PB4
dir_pin: PB3
enable_pin: !PC3
microsteps: 16
gear_ratio: 42:12
rotation_distance: 26.359
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
min_temp: 0
max_temp: 260
pressure_advance: 0.050
# Deine PID Werte (aus dem Log übernommen):
#control: pid
#pid_kp = 31.519
#pid_ki = 2.020
#pid_kd = 122.925

[heater_bed]
heater_pin: PA7
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
min_temp: 0
max_temp: 100
# Deine PID Werte (aus dem Log übernommen):
#control: pid
#pid_kp = 69.066
#pid_ki = 1.319
#pid_kd = 903.898

[heater_fan hotend_fan]
pin: PC0

[fan]
pin: PA0

# --- SONDEN & LEVELING ---
[bltouch]
sensor_pin: ^PC14
control_pin: PC13
x_offset: -31.8
y_offset: -40.5
#z_offset: 0
probe_with_touch_mode: true
stow_on_each_sample: false

[bed_mesh]
speed: 120
mesh_min: 10, 10
mesh_max: 200, 194
probe_count: 8,8
algorithm: bicubic

[safe_z_home]
home_xy_position: 147, 154
speed: 75
z_hop: 10
z_hop_speed: 5

# --- SYSTEM ---
[virtual_sdcard]
path: /home/johannes/printer_data/gcodes # Pfad auf neuem System anpassen!
on_error_gcode: CANCEL_PRINT

[pause_resume]
recover_velocity: 25

[display_status]

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh 2026-01-13]
#*# version = 1
#*# points =
#*# 	0.142500, 0.052500, -0.007500, 0.010000, -0.027500, 0.010000, 0.080000, 0.172500
#*# 	-0.010000, -0.052500, -0.092500, -0.092500, -0.110000, -0.090000, -0.035000, 0.055000
#*# 	0.085000, -0.002500, -0.040000, -0.060000, -0.085000, -0.047500, 0.002500, 0.072500
#*# 	0.095000, 0.035000, -0.010000, -0.010000, -0.030000, 0.012500, 0.070000, 0.125000
#*# 	0.137500, 0.060000, 0.020000, 0.005000, -0.025000, -0.002500, 0.052500, 0.115000
#*# 	0.167500, 0.100000, 0.022500, 0.022500, -0.005000, 0.020000, 0.080000, 0.142500
#*# 	0.180000, 0.110000, 0.030000, 0.027500, 0.000000, 0.067500, 0.097500, 0.140000
#*# 	0.127500, 0.070000, -0.002500, -0.002500, -0.022500, -0.005000, 0.075000, 0.155000
#*# x_count = 8
#*# y_count = 8
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 10.0
#*# max_x = 199.98000000000002
#*# min_y = 10.0
#*# max_y = 193.96
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  0.192500, 0.107500, 0.022500, 0.142500, 0.340000, 0.135000, 0.115000, 0.182500
#*# 	  0.082500, 0.005000, -0.057500, -0.015000, 0.050000, -0.032500, 0.002500, 0.085000
#*# 	  0.132500, 0.047500, -0.017500, -0.010000, -0.057500, -0.070000, 0.030000, 0.130000
#*# 	  0.185000, 0.117500, 0.062500, 0.015000, -0.027500, -0.007500, 0.067500, 0.155000
#*# 	  0.205000, 0.130000, 0.040000, 0.010000, -0.012500, -0.020000, 0.092500, 0.145000
#*# 	  0.240000, 0.167500, 0.077500, 0.050000, -0.002500, 0.007500, 0.095000, 0.160000
#*# 	  0.272500, 0.197500, 0.102500, 0.030000, 0.007500, 0.005000, 0.085000, 0.145000
#*# 	  0.202500, 0.137500, 0.050000, 0.015000, -0.015000, -0.012500, 0.082500, 0.155000
#*# x_count = 8
#*# y_count = 8
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 10.0
#*# max_x = 199.98000000000002
#*# min_y = 10.0
#*# max_y = 193.96
#*#
#*# [bltouch]
#*# z_offset = 3.025
#*#
#*# [input_shaper]
#*# shaper_type_x = mzv
#*# shaper_freq_x = 40.6
#*# shaper_type_y = mzv
#*# shaper_freq_y = 41.0
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 31.914
#*# pid_ki = 2.066
#*# pid_kd = 123.269
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 68.601
#*# pid_ki = 1.270
#*# pid_kd = 926.114
#*#
#*# [bed_mesh 2026-04-02]
#*# version = 1
#*# points =
#*# 	  0.202500, 0.120000, 0.025000, 0.152500, 0.347500, 0.142500, 0.120000, 0.185000
#*# 	  0.090000, 0.017500, -0.047500, -0.005000, 0.057500, -0.027500, 0.005000, 0.087500
#*# 	  0.137500, 0.060000, -0.012500, 0.002500, -0.052500, -0.065000, 0.032500, 0.130000
#*# 	  0.195000, 0.127500, 0.067500, 0.025000, -0.025000, -0.002500, 0.070000, 0.152500
#*# 	  0.210000, 0.137500, 0.040000, 0.015000, -0.010000, -0.012500, 0.085000, 0.145000
#*# 	  0.242500, 0.172500, 0.077500, 0.057500, 0.002500, 0.007500, 0.100000, 0.160000
#*# 	  0.277500, 0.202500, 0.102500, 0.037500, 0.012500, 0.007500, 0.087500, 0.147500
#*# 	  0.217500, 0.147500, 0.050000, 0.025000, -0.010000, -0.012500, 0.080000, 0.150000
#*# x_count = 8
#*# y_count = 8
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 10.0
#*# max_x = 199.98000000000002
#*# min_y = 10.0
#*# max_y = 193.96